Search results

I didn't think about that but you may be correct. I'll look back in my manual and read about setting up widgets. I did this so long ago I don't remember how I went about that.

I would agree with you. What's strange is that it is showing a temp reading for cylinder 4,5,6,7,8,9 and nothing for 1,2,3. The way I have my EMS1 and EMS 2 setup is that EMS2 has cylinders 1,2,3,4,5,6 mapped and EMS1 has 7,8,9 CHT and EGT. In addition when I go to the Debug menu it shows that...

Yes, I have two EMS. I built the airplane 10 years ago, All was well until the software update.

I had a fresh battery when I started trying to troubleshoot. I was at it for awhile and finally took the pictures before it shut down so I could post on the forum.

Hoping someone can help me troubleshoot the EMS on my radial. This is installed in a Pitts model 12 and has worked flawless for 10 years. Against my better judgement I recently went ahead and updated the software in my early version sky view. Everything appears normal other than I don't have an...

Still having issues. There must be constant noise coming from my screens that keeps my music input on the intercom muted 90% of the time. I have tried the suggestions above with no luck. If I remove the 3 wires (audio L, audio R, and GRD) that connect the sky view screen directly to the intercom...

I have tried a different headset. Noise only audible when the sky view display is powered up. Im assuming it is probably a grounding issue. In the diagram it shows the wires that run between the intercom and display as only twisted wire and doesn't indicate it should be grounded anywhere. I had...

Im trying to troubleshoot an audio issue. When I power up my skyview screen I get lots of noise in my intercom right about the time the Dynon emblem fades away and the self test starts up. The noise continues while the screen is powered but not as noticeable. This problem happens even with the...

Put the 1 amp fuses in line and had a brand new one that was bad. Didn't expect that and assumed I had it in an unsuitable place. Thanks

I have installed the Dynon shunt. Upon installation I expected to turn on the unit, map the sensor and see the draw from my battery. It only shows a red x. Not sure if I have it installed in the appropriate sequence. I have it in line between my battery and the master switch. Is this an...

Mel, you are brilliant. When I went to approx 60% the RX went away. Thank you!

I have my Dynon radio and intercom installed. Powers up fine all looks good except the radio continually shows RX and is receiving a transmission. If I disconnect the antenna cable from the antenna it obviously stops immediately. Both the pilot and copilot PTT's appear to be working properly and...

Thanks, I think that would be from the intercom to the SV. I have come to the conclusion that the com radio connects to the skyview display via a 9 pin network cable. Hopefully this is correct.

Please forgive me if this has been explained already and also for my ignorance...but...I cannot for the life of me find a diagram indicating how to connect the Com panel D9 to the skyview display. Thanks

While on the subject, what type of hose (material) is recommended?

Ok, I was able to transfer the file to my skyview. The sensor is coming up on my screen but I have a couple of problems. One of which is that there are 10 places to the right of the decimal which is an easy fix. The other one is that I cant get it to come off 0 psi. I am only able to put about...

May have answered my own question but I opened the .sgf file with word and added on the settings you recommended. I will attempt to load them tomorrow and give a report if it worked. Thanks

Good thing you are asking the question now because I would ask the same one in a few weeks when my transponder finally shows up :-[

you guys are great, thanks for the quick response. I am able to save it using your suggestions but my computer doesnt know what program to use to open it so I can make my modifications. Maybe I have to modify it then do the save as thing. Any suggestions?

How do you know if you have oil pressure after startup if you don't have your avionics on?