Search results

  1. R

    I connected the N16 to my AFS 5600 system not the skyview. However, it will also connect to the...

    I connected the N16 to my AFS 5600 system not the skyview. However, it will also connect to the skyview. You need the N16 radio as well as either a Vega or Razor control head. If you have the panel room I recommend the Razor because it has a bigger display and is easier to read. The control...
  2. R

    Another shear screw

    Thanks, I'm aware of the instructions and followed them closely. Red loctite is included with the shear screw replacement kit from Dynon.
  3. R

    Another shear screw

    Thanks, that's good to know. I was mostly concerned about them being held in with red loctite. Usually anything installed with that is very difficult to remove without heat. In this case maybe the screws are so small there's not much for the loctite to hold onto.
  4. R

    Another shear screw

    Thanks and you are correct. I got a reply from Dynon Service and the disk (I called it hub in my OP) is not field replaceable. It would be extremely difficult to remove the remnants of the shear screws from the disk so a return to Dynon would be required.
  5. R

    remote NAV radio for SkyView HDX

    I have a N16 installed in my aircraft as a backup. I only bought it because it was the least costly way for me to satisfy Transport Canada’s requirement for a second independent nav source. They won’t accept Dynon GPS as an IFR backup. I’ve found that it’s actually a really great radio. It...
  6. R

    Another shear screw

    I've broken 2 shear screws in my RV-10's roll servo over 4 years and 450ish hours. The original broke a couple years ago and it was chalked up to a weak batch of pins. The second one was one of the newer screws that is supposed to have better fatigue resistance. It broke a couple days ago on...
  7. R

    Yaw damper

    Is the yaw damper available for the RV-10 now? It's one of the reasons that stuck with Dynon products for this project when I saw that Rob had it in his RV-10 but I haven't seen an announcement of it being ready to purchase.
  8. R

    fuel flow transducer

    I've been using the red cube in my Glastar since I installed the Skyview when it was first released. It's never been an issue and is within 1% accuracy in the gravity flow system feeding my 180hp O-360. It has been well tested and proven at extreme angles of attack and full throttle.
  9. R

    Wi-Fi adapter FAULT

    I was getting the same error this morning when I tried to set up my system. I had my aircraft identifier set as C_GDWH in aircraft information. I had to change it to CGDWH, no _ in between the C and G. It is now showing online. With the underscore in place the wifi setup was showing a space...
  10. R

    CHT/EGT rise when PTT is depressed

    I just got an email back from Dynon Support. Turnaround time for the repair is 10 business days after receipt at the repair shop. With shipping both ways I'm probably looking at 3 to 4 weeks down time. The problem is not annoying enough for me to stop flying for a month to get it fixed. I'm...
  11. R

    CHT/EGT rise when PTT is depressed

    So we actually have to take our planes out of service for how long to get this fixed?
  12. R

    CHT/EGT rise when PTT is depressed

    I set my EGT and CHT alarms to turn off automatically once the "red" condition is no longer present. I, too, am looking forward to the new EMS module. If you use the leaning function and have to key the radio before you're done you have to start from the beginning.
  13. R

    Dynon closed for Christmas Holiday

    Merry Christmas to all of you at Dynon and to all members of these forums. I wish you all the best in 2012.
  14. R

    CHT/EGT rise when PTT is depressed

    Mine do the same thing. I've tried shielding the wires, moving my comm coax and added a bonding strap to the EMS module but it didn't make any difference at all. I read in a previous post that the L-Comm d-sub filters remedy the problem but I have not ordered them. L-Comm wanted over $50 for...
  15. R

    Canadian Airports as User Waypoints in .dup format

    Thanks for making this available, Perry. I downloaded it but will probably not use it until next summer.
  16. R

    EMS Sensor Definitions (Changed on 3.2)

    I upgraded to 3.2 (from 3.1.1) including the sensor definitions file and my Layout was unaffected. You do not have to upload a new EMS layout file, just the definitions file. The only change I noted in EMS layout was my "fuel remaining" font was a little larger than it was so I had to adjust...
  17. R

    Dynon USR Export utility. Where is it?

    Try here: http://dynonavionics.com/downloads/DynonUSRExportSetup.msi I tried to attach the file here but received an error. it may be too large to attach to a post.
  18. R

    CHT and EGT off scale when transmitting

    Does anyone know of a source for the L-Com filters besides the L-Com website? They want $43 for the part and $65 for shipping to Alaska. The shipping seems quite excessive for 3 little connectors that can fit in an envelope. I inquired with Dynon Tech Support but they do not supply the...
  19. R

    CHT and EGT off scale when transmitting

    I have the same issue in my Glastar.  I've shielded everything, added grounding braids and even re-routed the comm cable so it ran nowhere near the EMS module, nothing worked. After reading this post I followed the link to buy the filters. Some of the the filter modules are currently out of...
Top