Search results

Great information. Funny, I turned off Info item 5 thinking that was the issue. I didn't try item 4. I had recently added info boxes not realizing one would block out the Status box. thanks!

I have dual SkyView Classic screens, 10 inch and 7 inch. I used to have a box in the lower left corner of the map page that was for ADSB Status, It gave info on status of Next Rad and age of display. The box in no longer there. Where did it go? Secondly, there is a box on the right side of the...

That was it Kurt! My GTN was set to ADS-B on the RS232 output. I changed it to ADS-B+ and now my system is compliant. Thanks all for your suggestions.

It's configured to "GPS DATA: GARMIN ADS-B/ADS-B+" See attached pic of set up page.

I checked it today with my plane outside receiving good satellite GPS data and it still says "no" for 91.227 compliance. I checked my records on the wiring : my GTN650 is directly connected from pin 7 (RS-232 out 2) to pin 3 on my SVXPNDR-262. The note on my SV setup page says my GPS data is...

Dynon, I have a SkyView system with software 15.1 with your transponder I bought three years ago, it is fed by my Garmin 650 for GPS information, an ADSB 470 installed yet my setup page says I am not 91.227 compliant. One of your reps at Sun n Fun said all I need to do is install the firmware...

I had my system tested a couple months ago and "my guy" who said he has tested other Dynon systems said he has never had a  problem by slowly (very slowly) raising the altitude and slowly lowering it. We also connected his test box directly to all three ports on the ADHARS so pitot, AOA, and...

Just for the record, I have seen the same ghosting issue with my SkyView system. I'm flying a Glasair III with a dual SV system. I have seen the ghost target before and after update 12. I wonder if there is slight time delay between my transponder, ATC, and the ADSB receiver creating what my...

I read the pilot users manual and figured out how to select the GTN to display on the map. I flew multi waypoint flight and it worked perfect. Thanks

Carl, I did wire my GTN650 through the Arinc interface exactly as the SkyView install manual dictates. I didn't know how or that I had to select it on the SkView flight plan. I will look in the pilot instructions for how to. Thanks for the information. Don

I have a dual Dynon SkyView and a GTN650. I selected and activated a GPS approach on the Garmin but didn't see it on the map. I was able to show the course needle on the HSI and fly the course, but I don't know how to make it display on the map page if that is possible. I also can't show the...

Ok, I may already know the answer to this question and it may have already been addressed on earlier discussions. I was taxing down wind on a long taxi way with a 20 knot tail wind. When all of a sudden "GPS ASSIST" pops up on the PFD. When I turned to hold short of the runway it went away. So...

Yes i sent the the EMS unit you sent back. It was a reman unit and still had a problem. I talked to Mike on the phone about it. I put my original EMS unit back in my airplane, put a new EGT probe in and now it work great. I still have an issue where the manifold pressure reading goes to full...

Only when transmitting. At the low end of the frequency band (118.00) the MP goes full scale. At the high end (136.00) it only increases about a third or less.

I finally determined the bad EGT reading was an intermittent probe. I have one on order to replace it. I had Dynon send me a replacement EMS and it did the same thing but even worse. With everything hooked up all the CHT and EGT readings went to full scale. The unit was a remanufactured unit I...

My plane is a Glasair III with internal di-pole foil antenna, one in the vertical stab and one just behind the seat back. I believe the coax is RG 400 or similar, that Glasair provided with the kit. I am in communication with tech support on my private email and considering an RMA because I now...

Very cool, Im' considering putting a camera on the belly of my Glasair III hoping to capture the landing gear as a backup gear indication.

When I designed my panel layout for my dual SkyView I fashioned the remote USB ports to be flush behind my glove box door. I figured they would be neatly out of sight and accessible for software updates and sensor downloads. I figured I would use the ports on the back of the units for the charts...

I reported a similar issue a few weeks back to Dynon Support. My manifold pressure indication and my No.2 amps (hall effect) would peg out when either comm were transmitting. Dynon suggested to check the coax or have a radio shop check for RF leaking. I haven't had access to the shop yet, but I...

I have a Glasair III with internal mounted foil strip antennas , a Garmin 650 nav com and a Garmin 225 com and dual SkyView. When I transmit on either com my manifold pressure indication and my No. 2 amps indication goes full scale. Thanks in advance. Don Yoakley Any ideas?