Search results

People have done this, usually with success. The angle is shallower than 45 degrees, but it's also more of a complex shape that's designed (and wind tunnel tested) to be less sensitive to yaw. The pitot port on our AOA tube is also designed to be insensitive to AOA changes.

So the EMS wiring is almost identical. Other wring is somewhat different. The remote compass wiring isn't the same as the ADAHRS in SkyView, for example. But the fact that the EMS sensors and wiring almost transfer exactly over makes it not too bad at all. We don't currently have a trade-in...

1) We don't have a date, but some features are in beta 2) AP improvements should be across the board. The core subsystem is pretty model-agnostic. 3) The features have ebbed and flowed, but some of the major ones are support for the new ADS-B wx products, improvements to vertical navigation...

It's true that our Dynon Certified efforts have redistributed our development resources some, and that we haven't had as much velocity on our experimental release this time around. There are also some other projects that we're not talking about yet that have been competing for priority. We think...

The AP74 does not have a serial interface. However, the EFIS that it is connected to does, and can be connected.

It should be fine. The software on the EDC-D10A hasn't actually changed in quite a few software versions.

Yes, the serial to gray code converter is still available. It was originally designed for our D10/D100 series, but it will also work with SkyView using one of the display's serial outputs.

Sorry that you're not having an awesome experience here. We think we have explanations for all of the things you experienced, but there's a chance there's something up here. So, a few thoughts: First, check under SETTINGS > INACTIVITY TIMER. If that's set to the 15 minutes setting, the D3 will...

It's super rare that we don't figure out what's up with something after we've had it here for repair, and all products go through multiple stages of both machine testing and human verification before they go back to you. All that said, it looks like this is probably hardware, and not something...

There's both a full calibration that you definitely should perform, under SETUP>MAGCAL. There is also a manual adjust under SETUP>MAGADJ. But, our best advice is to make sure to read the full instructions on how to use these calibration tools in the installation manual, which is available at...

So we actually did check into offering this ourselves, and for various reasons, but topped by a lack of strong demand, we didn't end up bringing it to market. That said, here's both the supplier and the specs that we were looking at. They'll sell in small quantities to individuals, and have a...

We think there's a bug in the support program that we don't quite understand, and probably won't fix because it is super rarely encountered. However, searching through our support archives, I think there may be a workaround. It's a little complex, but here's something to try: Make sure that...

Sorry for the lack of updates. We actually had a breakthrough on that and are hot on the trail of a fix. It's a little bit complicated, but we think it should make it into the next release.

We wouldn't expect a software mismatch to cause the display to shut down, but it would definitely cause things to not communicate and work together. This smells like it might be a hardware thing, but it's worthwhile to try updating the software on that display. After it does its power down...

If either of the servos' disconnect wires are grounded (button pressed), the AP will disconnect. There is no way to disable that, for safety reasons (exception/caveat - on a servo used as a yaw damper, the disconnect switch is used instead as an optional toggle switch with each momentary press)...

We've seen this too - I've filed a possible bug report with our engineering team.

It can be repaired. Give our support team a call at 425-402-0433 or via https://www.dynonavionics.com/contact.php

Definitely not expected bahavior. Give our support team a call at 425-402-0433 or at https://www.dynonavionics.com/contact.php for more help with this issue.

To confirm, we wouldn't expect to be compatible with the KX155, as it only has the analog resolver interface, and no compatible ARINC or RS232 outputs.

That's odd indeed. If you haven't already, get in touch with our technical support team at 425-402-0433 or at https://www.dynonavionics.com/contact.php