Search results

Never Mind, I found it myself: http://www.dynonavionics.com/downloads/Install_Guides/RV10%20Pitch%20Kit%20with%20LA%20Instructions-REV%20A.pdf I have sent an email to support to see how we can resolve. Rudi

Arhh no man, what is this SV42 "T" servo? I just installed my SV42 in my RV10 but I see the recommendation changed? I hate doing re-work. Dynon Support can you help? here is what i did last week.... Thanks Rudi

Hi Dynon, Bump! Rudi

What is a virtual VOR? An imaginary waypoint that can act like a VOR?

Good to see a lot of people at the same stage, Dynon Support can you please give us more information, on how to wire it before the official release? Rudi

Good it is online now I can see Revision J!

Thank you! On your Answer 2) Sorry Online you have Skyview 3.2 Revision I September 2011, it contains nothing about the GTN650. What am I missing or which documentation are you referring to?

Thanx, I was literally going to do the Audio wiring tonight. So Any information will be really useful. I can delay a day or two, but then I am closing the panel up. So please share what you can...I am wiring into an audio panel (Unswitched Mono Input) what should I do? Thanks in advance...

Thanks, it does. I will keep them independent each GPS to each Display. Thanx

Bump, Q1) Busy with wiring, have a GTN 650 via Arinc, is it fixed now in 3.2.2 Q2) and is the wiring as suggested in the top post picture? Q3) is the serial in PIN 3 on the ARINC module still required? Thank you in advance, Rudi

Skyviewers, I know the audio wires should not be connected now, due to noises, but it is easy to do now while i have access. I know the D100 range (previous generation) had a Variable resister to control the volume. So to Dynon, what Variable resister can I fit to these lines, same as the...

Skyviewers, I am confused, how to wire Dual SV-GPS-250 to 2 Skyview Displays... P8-3 "If there is more than one SV-GPS-250 in your system, use the same scheme in fig 47 but on different display serial ports fo the othe SV-GPS-250 modules, but connect power and ground 'together' I also found...

Ditto when is 3.3 expected?

Gents, I'm busy with my Skyview installation and have 3 questions, before I cut and route some network wire through the aircraft. I have the redundant configuration as per the diagram below. 1) Can I swap the daisy chain position of the components on the network to any place. i.e. both my...

To Dynon Support, A week or two has passed do you have any more information? Thanks Rudi

Our RV12 has a standard duel screen setup D180 + D100, Our screens exchanged comms with the GPSMap 495 just fine. Then we upgraded to 5.4.0 and v2.70 on the GPSMAP It reset the standard previous comms settings and now we dont get comms between the screens and GPSMap 495. What settings should...

After cutting those lines we noticed to AltEnc info going to the Transponder is missing since it does not display anything, so we had to reconnect those lines...I wish we had a RV12 wiring and pin-out diagram it would making resolving this problem easier.  :-/ Now after updating we dont have...

Ok we resolved our rv12 duel screen problem. We had to cut the rx/tx lines that runs to the rv12 control board dsub37 connector it gave us problems. Then we only had to have 1 screen powered up at a time during updates since both screens share the same rx/tx lines

Redmark, did you ever get it resolved. Dynon Support, any other RV12 owners reporting the same? we sit with exactly the same problem, RV12 with D180 and D100, Both Screens go Yellow. We have tried 3 different laptops, Win 7 64bit, Win 7 32 bit, Win XP. All give the same Yellow screens on...

Excellent NEWS! Well Done and I cant wait!