Search results

Seems lot's of my sensors are out of whack. Carb temp is stuck at around 35 degrees while OAT is over 80. Any ideas?

My Skyview continually shows me in a skid. The aircraft is in coordinated flight and the ball is off center to the right about 1/2 ball. Is there an adjustment that can fix this? When I step on the ball it is obvious I am uncoordinated and the airspeed drops accordingly.

Okay, that helps.

Thanks! I looked in the P-mag installation instructions and bingo, there it was 2 PPS!

I hooked up the battery back up to the connector the harness came with. It goes to the DB 37 Skyview directly and not to EMS. I believe its PIN #2 (P2). The "screen hardware information" indeed shows the backup battery voltage. However, when displaying a "widget" on the ems page the "back up...

My Skyview backup battery indicates 0.0 volts. When I put a meter directly onto the backup battery it shows 11 volts (slightly discharged). How to I get Skyview to read the backup battery voltage? The sensor configuration is correct (P2) .

How do you know what the pulses per rev are supposed to be?

I have an o-320. I could not find in the set up where I could adjust the RPM settings.

Hello, I did a first engine start today and had a higher than normal RPM indication (about 4-500 across the various power settings) Idle was about 1000 and what would normally be about 1000-1200 RPM indicated 1800 or so. (I estimated RPMs based on sound) I have dual P-mags with 12V Standard...

That was the message I got also. "Corrupt or missing storage device. Contact Dynon" However, I was running off a power supply and I now believe it wasn't grounded properly. I haven't seen that message when using ships power or the backup battery.

Will do.

I had the altitude display at around 100k also. That was just after installed the HD terrain file. After I rebooted it was fine. I powered up SkyView several times today using the ships battery with no boot errors. Right now I think it might be related to the power supply that I was using to...

Ron, make sure you update here if you find a solution. I will do the same. I am a bit uncomfortable as I have a single Skyview and no back up flight instruments. Of course VFR I don't need anything (to land). Makes me consider expanding my Skyview to a second unit or finding a backup flight...

Hello, I powered up my Skyview today, as I have more than a dozen times, however on the main Skyview Logo boot page the screen locked. An error message at the top said something to the effect "cannot access drive - contact Dynon support". I did just that. Dave helped me reboot using the 1,2 & 5...

Both Ray Allen trim servos and the MAP connect to the PIN 18 white/red +5VDC output on the EMS D37 according to the installation instructions. The current is limited on that circuit to 500ma. I assume this is correct and won't put a strain on that circuit?

I understand not including the AP diagrams in your install instructions until the AP is officially released. Just on my side, I am trying to finish all my wiring and keep hitting road blocks, not your fault, just would like to "get r done"!

I know SL30 interface is not available yet. But anyone got a clue what the pin-outs will be for SL-30 to SkyView?

Okay, just want to make sure on this one. I need to install my AP servos. I plan to use a single splitter. Are the splitters polarized? That is, the splitter has one male (pins) and two female (socket) ends and comes with a gender changer. Does it matter how I hook this up? Okay, so I found a...

I cannot find in the installation manual what the D9 connector coming from the D37 connector (pins 11,12,30) is for? Frustrated!

Looks like I need 2 splitters. That is what I was missing. 1 SV-1000, GPS, Batt, 1 ADAHRS, EMS, 2 AP Servos. Each item you add to the network requires a splitter.