Search results

I just upgraded my IFD540 to version 10.3 and am having several issues, all regarding the WiFi connection. My system is a Dynon Skyview D1000T, with the ABS-B 472 Receiver, and the IFD-540. The upgrade to 10.3 went fine. No errors. I enabled the Weather/Traffic over WiFi in the configuration...

I just upgraded my IFD540 to version 10.3 and am having several issues, all regarding the WiFi connection. My system is a Dynon Skyview D1000T, with the ABS-B 472 Receiver, and the IFD-540. The upgrade to 10.3 went fine. No errors. I enabled the Weather/Traffic over WiFi in the configuration...

Avidyne released software 10.3 on Wednesday. One of the big changes is it allows the Avidyne to display ADS-B weather and traffic from other devices as long as it is on Wi-Fi and using Port 4000. I installed version 10.3 on my Avidyne but unable to display any ADS-B products. The IFD is...

It started the first time on my D1000T classic system with version 16.3.0. It continued with 16.3.2. It is intermittent, once in 5 to 10 flights. It requires a total skyview reset or disable Skyview WiFi adapter and re-install to correct.

You have to be on the final inbound course, and below glide slope. The glide slope needle needs to be present and above you. Also, if you are in a decent, like descending to a FAF (PEYIP in this case) and you hit the VNAV button the decent will stop. It will level off until it intercepts...

I have had my WiFi fail to communicate with my Foreflight tablet about 3 times over the past few months. In all cases it starts off fine then in-flight Foreflight drops my position data and shows no track or any info on flight progress. No more ADSB data. Looking at the WiFi status it shows...

I noticed the audio is louder after this upgrade. I noticed the autopilot audio announcements are louder. But not as loud as you described. I observed no other issues. kurt

Have you thought about vapor lock. Sounds like you may have bubbles in the fuel. Is there any other indication like fuel or oil dripping out of the diaphragm port? This is the drain port between the two diaphragms on the mechanical fuel pump. Kurt

I changed my GNS430 to an IFD540. The serial to the transponder is still set to ADSB OUT +. Same as the GNS. kurt

BTW, If you are using FlyQ it will crash with the IFD on the Skyview network. This is due to the network having two GPS sources. Skyview and the IFD. The FlyQ is totally confused and try to const. switch between the two GPS sources. Foreflight has enough logic to pick the best source...

The problem come into play when you try to push a flight plan from Foreflight to the panel. Foreflight will show two devices that can accept a flight plan, Skyview and the IFD. Foreflight has no way for you to select which device to send it to. So, when you push to the panel it will pick...

I have done this with my Skyview classic touch and my IFD 540. You have to configure the IFD to the same network as Skyview. You must setup the IFD in the configuration pages as a remote / join network device so it joins the Skyview Network. in that setup page you enter the Skyview name and...

Are you using VPN? It will not do flight plans if you use VPN. kurt

So if you have 2 P-Mags, both at 2 PPR, then you do not have this problem?

Just press and hold the baro knob. It will automatically grab the closest baro setting. I also have my Foreflight bottom line display nearest baro. That way I can see it change and tune it in before the message comes up. Kurt

Most likely a broken / intermittent wire. check any bayonet connections and also check the D 25 connector at the EMS module for a pushed in pin or socket. kurt

Looks like everyone using version 16.0.4 needs to push this patch. Seems like ever couple weeks a new symptom of this bad date issue shows up. Original post had issues with weather and traffic. I had issues with the user log files. Now what seems to be an another traffic drop outs. Dynon...

Once Avidyne version 10.3 is available it promises to allow the Skyview traffic and weather to transfer to the Avidyne screen via WiFi. This is the first time I am aware an IFR navigator that will accept weather or traffic from a WiFi source. The Avidyne 10.3 is currently in the FAA approval...

After loading the Patch and clearing out all the User Logs. I flew today, downloaded, and uploaded logs to SAVVY. All appears to work correctly! So, now Is it possible to modify the "bad" DATA LOG file? I tried taking a single days flight out of the original USER DATA file and paste it...

thank you! I have loaded the file and cleared the data logs. I will fly later this week to test it out. Thanks, Kurt