Search results

There are built-in leaks on both the pitot and AOA ports, so if you were to blow into one of them and plug their respective lines, you would have air leak through their drains. BUT, if you aren't getting ANY flow from the AOA port when it's unrestricted, you might have a blockage in there. If...

So from the description, it sounds like the transponder might be restarting, or its data connection to SkyView might be intermittent. So the first thing to check are all of those connection points. The next place that might shed some light would be the alert logs, which export with the user data...

Hi Alan, I think this might be the first report of this behavior we're hearing, but we're happy to look into it. A couple of questions: Do you have 1 or 2 SkyView displays? And once SkyView is powered on and fully booted, does the wifi status in the wifi setup menu show anything amiss? Or...

The blue screen is what you'll see when there is "no signal". It's essentially masking the static picture that the otherwise no-signal would otherwise produce (think old VCRs/TVs). When you PTT, you're changing that no-signal slightly with the nearby RF transmission. When you have a TV or active...

They are important for rejecting EMI interference. The wire pairs should be twisted at 8-10 twists per foot over the entire length of the cable.

As Rays says - both the "CAL?" and the lack of indication on the trim widget means that they haven't been calibrated / configured. If they were, but sensors were disconnected, you'd get either a "red x" over the sensor, or the sensor will be all the way at one end of its reading (depending on...

Also, can you get a Dynon Diagnostic File and send it to us? Instructions are at http://www.dynon.aero/reportlog. In the message area, put "case 246550".

Looks like there might be a bug there - we'll need to investigate / reproduce here. Without knowing more at this moment, your best bet will be to do the test while your 201 is primary so that the software "sees" both. If you go into the normal source selection screen in PFD SETUP, does changing...

Agreed. Under the Q&A it identifies it as the 100425-00 harness. But it needs to be much clearer. Thanks for bringing this to our attention. The bottom line is that you don't have the harness that the STC specifies. Now, that doesn't meant that your installer can't approve it - they can choose...

There are some images in the literature in http://www.dynonavionics.com/product-literature.php that need updating from earlier prototypes, but the docs http://www.dynonavionics.com/drawings-cad-models.php here should be OK, with a 2mm discrepancy in depth (the "can" got very slightly deeper...

Looks like it's not in v15

If you're seeing OFFLINE, that likely means that ADAHRS isn't working (unpowered, broken, or perhaps at some point a SkyView Network Configuration was performed without the second one connected?). Check the network status page next. Also, if you can see it, there's a light on the physical ADAHRS...

Let's back up a step. There are two harnesses available for the EFIS-D10A. The original - 100425-000 - has a serial port like you describe, without the power supply for the GPS-251. The newer "simplified" harness - 102832-000 - has fewer overall wires for simplicity, but does carry power for the...

Something's not adding up here. Are you using the SV-AP-PANEL? And how exactly is your emergency switch wired into everything? We generally wouldn't recommend using an emergency switch like you've wired - the SV-AP-PANEL already has failure circuitry that will allow the pilot switch to continue...

So to be clear - Dynon servos can only be controlled by Dynon EFIS systems. They operate over a fully redundant data link, and the actual techniques we use to drive the servo motors are proprietary. There might be other enthusiasts that may chime in though!

Sorry about that. The forum is designed to be a community - one that we provide and take part in - but as a support mechanism, it's not staffed by our technical support team. We try to get to everything here within a day or so, nonetheless. If you do need more timely and personalized support, I...

It isn't. We did have a few days of our support system not working quite right, although we thought we thought we caught all of those cases. Looking into this...

They should both show. If you go to SETUP MENU > PFD SETUP > ADAHRS SOURCE SELECTION, do both ADAHRS show as online? If not, you might have a connectivity issue. What does your SkyView Network configuration show? If they both show as online, what does the COMPARE button on the ADAHRS SOURCE...

We change our pricing structure rarely, and we try to be as straightforward as possible. Here are all of the changes we made at Oshkosh 2016: 1) We introduced SkyView HDX at a higher price point than SkyView Touch/Classic. 2) We offset some of that increase by - simultaneously - including the...

You'll see that message whether you're in flight on not. You might pre-emptively pull up the comparison screen before you see the message so that you can better see what's going on. That's in IN-FLIGHT SETUP > ADAHRS SOURCE SELECTION > COMPARE (button on menu). 1) This message means that the...