Search results

That is what I did. I didn't see any other way around it...

Just a follow-up on an old post with some great news!! I upgraded to version 2.5 today and I was excited to see my GX60 start talking to the SkyView!! On the PFD screen when you select Navsource I now get info sent to the HSI from the GX60!!! Thank you Dynon!!! -Mike Kraus

http://dynonavionics.com/cgi-bin/yabb2/YaBB.pl?num=1269001194 Read the end of this thread. It says it is a network device, so I assume it will be powered thru the network like the EMS module or ADHARS modules.

That will work for me, I have the Dynon GPS, and a Garmin 696. So I'd be happy with it working as a HSI input. Thank you for your continued work on this!! -Mike Kraus

Thanks for the feedback, I was litterally walking into the hangar to rivet on that top skin. Had I done so, it would have turned a 4 hour job into a 30 hour job..... I'll order up my new probes tomorrow. Are my Blue Mountain EGT probes gonna be OK?

Hmmmm, so I have the same probes from my Blue Mountain and I assumed they would work as they read accurately at room temperature.... I read your note and was literally heading out to the hangar to rivet on my upper skin between my IP and firewall. I pulled a CHT probe and stuck a heat gun to...

Typically the PPR is set at 1/2 the # cylinders. Your o320 should be set at 2PPR.

Typically the PPR is set at 1/2 the # cylinders. Your o320 should be set at 2PPR.

What engine? What is your pulses per rev set at (under ems settings, engine info). -Mike Kraus

OK, I have serial 1 outputting Dynon Converter, 1200 baud to the GX60 and sL70. SL70 has to be set to 1200, GX60 defaults to 1200 for this input. I am receiving altitude info from the SkyView to both the SL70 and GX60, no problems. But I still can't get the SkyView to receive the course...

No better luck. I have the SkyView successfully talking to the SL70 transponder using 'Dynon converter' (not Icarus), but it is NOT talking to the GX60. Dynon, know you are busy but is there anything on your end you see that we can do or any info you need from us to investigate a solution...

I had "enable extended movmap data format". Is this what you are referring to? -Mike

Sorry worded that wrong. I have the following set up SkyView: -serial 1 out=Dynon convertor, 9600' goes to GX60 serial 2 RX -serial 3 in=GPS3, generic aviation, 9600 goes to GX60 serial 1 TX GX60: CH. RX. TX 1. NAV. MovMap 2. AltEnc. None Enable External Moving map...

I have the encoder feeding the SkyView already. I think I had the extended Data enabled, but not positive. I can check tonight and try again. -Mike Kraus

Yes, my intent is to use the Dynon GPS for the moving map/ synthetic vision, and the GX for the nav source. I'll check what the GX60 outputs when I get home. -Mike

I'm running windoze xp. Who should I ask for when I call? I help in any way I can if you can get the GX talking to the SkyView!!!

Tell me how I can do a serial capture and I can do it tonight. I also have the install manual if that helps any. It discusses the serial code in it. -Mike

Thanks for the update. Is it safe to say you plan on fixing the SkyView to accept the GX60? Or will we need to utilize another GPS to get approach functionallity? I hate to have to upgrade to a 430, but now is the time before I rivet on the upper skin between the IP and firewall. It will be...

My GX60 is set to MOVMAP and it isn't working.... -Mike Kraus

OK, some good new, and some bad news (maybe for me...) I hooked up the system again. GPS 1 set to Dynon, GPS 2 set to Garmin 696 and GPS 3 set to GX60. I turned off everything except the Dynon GPS and got a signal (GPS 1 working). I then turned off everything except the Garmin 696 (GPS 2...