Search results

Is it possible to have Foreflight attached to skyview at the same time as Stratus II?

I tried to input magnetic inclination values into my skyview, but all the information I've seen says SETUP>MORE>MORE then insert the value, but I can't find the MORE after I hit the setup. Is it necessary to input the MAGINC in skyview, and if so where do I find it?

Just got my repaired d700 back a couplr of weeks ago after it was repaired for freezing up, and eventually not booting up at all, and now, over the last week it's started to freeze up again. Uploaded 4.0 last night. Seemed to run fine during taxi tests today, then froze up repeatedly as it...

Red wire was the problem! I used two different tables. The one specifically for the FT-60 says to use pin 15 Aux 12V, and the full C37 tables says NC for red, pin 15. So apparently I ran the wires using the first one because the red wire was right with the others at the connection to the...

Thanks. I thought I had it connected right via the Dynon instructions for the Jabiru engine (EMS C37), but I'll connect today, and see if magic happens! Thanks Mike

Now on to the next , and last skyview (operator) problem. The fuel flow sender. No indication. System recognizes the device, set at 38000 pulses. Got the red cube, hooked up blk to GND, wht to the yellow wire from the harness to c37 pin 14, and the red wire is not connected. I think the...

I think I've found the enemy and he is me. Grounding the bottom of the fuel probe in addition to the black box ground, and then "faking" the calibration, followed by editing the table gave me a reading. It isn't right, but at least it's something. Does anyone have a copy of the voltage...

I don't know what file you are referring to. Is the "1S" referenced in the MMarien message a file, and if so how do I get it? Obviously Confused

Skyview, with Princeton fuel sender. I have one 16 gal tank (Waiex). when I attempted to calibrate the device the table said 3.2 volts on every add cycle, but i elected to use it. I put full when the tank was full, and the calibration failed of course, but now it shows no reading. * I did...

D700 was freezing after about 1 to 2 min following bootup (this is all on the ground, have not had engine start yet). Updated the firmware to the latest file from the website. Finally got it updated (it first froze during update and had to be shut down). Following update it initially behaved...

Thanks.

Does connectorizing the GPS-250 leads to the Skyview D-700 have any negative signal or noise issues, and if not could "bullet" type connectors be used, or would a DB-9 be required?

Thanks, that clears it up. Mike

With the skyview system, gps 250 and Dynon servos, and the SV-270 Nav software will I have GPS steering, or do I still need a 429 interface? Mike

Thanks, I looked for that and missed it anyway! Mike

What is the appropriate nylon AN fitting to attach the 1/4"ID- 3/8"OD tubing for the static/pitot/AOA ports. I ordered what I thought was right from Wicks, but missed by a mile. Thanks

Thanks, that's good news. I'll get in touch to get a replacement shear pin. I'll bet the arm is just stuck to the surface, but I was reluctant to start prying, etc. Thanks, Mike

Back in May I got the right servos in hand to use a modified arm (longer than the long arm Dynon supplies, so I went to an sV-42 servo). Now that I've finally gotten the arm manufactured I can't figure out how to get the original arm off the servo and I fear that I've screwed the pooch. Once I...

Thanks, on with wiring! Mike

I've accounted for all the ground (black) wires from the DB37 both visually and ringing them out with an Ohmmeter, but there seems to be nothing connected to pin 13 on my factory harness (which according to the manual is supposed to be black/ground). I even rang out all the other wires. I...